ADC-F

Architectural Specifications:

Operation

The automatic door operator is to be fully electronic operator, housed in a fully anodised aluminum transom section (height 132mm x width 155mm). The unit shall be Scottish made by an Scottish owned company, must comply with BS7036-1996 and be equipped with self-diagnosing multifunctional microprocessor unit.

Prerequisites

The Automatic Door Operator is to be a fully electric operator, housed in an extruded aluminum low profile transom section (Height 132mm x Width 155mm) the unit shall be Scottish made by an Scottish owned company, must comply to BS7036-1996.

a) The equipment will incorporate electronic computerized DC Motor with
built in optical sensor for precise movement, high torque for a maintenance free life.

b) The pelmet shall incorporate an integrated and interlocking hinge for secure
closure and maximum cover. The design shall enable the operator to be fitted flush
to the ceiling when required, while the pelmet may be opened fully or removed for
access.

c) The multifunctional microprocessor control unit shall feature the following:

· Self-calibrating and programmable modes.
· Fully compensates door weight and friction therefore delivering the optimum force for efficient operation.
· Independent circuits for pressing closed at the end of the closing stroke.
· Provision for full interfacing with all types of building security/alarm systems.
· Open speed control.
· Closing speed control.
· Brake control: preventing the doors from slamming shut.
· End position-damping control for accurate slow down of door movement.
· Built in UPS (uninterrupted power supply; battery back up to allow the door to open) for continued operation of under power failure.
· Option of Solar power provision can be included.

d) The tracking system is to be dual linear track designed for accuracy and long service life fitted with anti rise wheels with no possibility of doors disengaging off tracks. The upper track shall be made of harder and stronger alloy.

e) Safety feature: Moving doors will automatically reverse when traveling in either direction, if obstructed, sensitivity setting to be programmable.

f) During a power failure or emergency the Failsafe device will fully open the doors. The failsecure mode will close and secure the doors until power is restored

g) Provision for climate control shall be available. Door opening can be restricted from 50% of normal door operation during high winds or low traffic situations.

h) Dual sets of sun resistant P.E. light cells flush mounted in the door jambs will prevent doors from closing if the threshold area is obstructed. Fitting of P.E. lightcells will be at 300mm and 600mm from finished floor level.

i) Door drive shall be by way of toothed belt reinforced with fiberglass tensile members, will incorporate nylon facing surface for pulley tooth protection, for silent and service free operation.

Installation

The manufacturer or the authorized service agent shall install the operator.

Functions

Following functions are to be selectable through a wall mounted key switch.

· Auto - Doors are operated automatically via the movement sensors.
· Open - Doors maintained in open position continuously.
· Exit - Doors remain closed activated only by exiting traffic.
· Lock - Doors remain closed and locked where optional electric lock function has been installed. Exit by way of emergency exit button.

Actuation

It shall be one of the following:

Microwave directional sensors
Flush mounted sensors
Passive infra-red sensors
Fine-line sensors
Remote control transmitters
Induction loops
Key card system
Fingerprint / Retina Scanners

Motor

The motor is brushless 24 volt DC with in-built optical sensor for precise movement, operation is silent and maintenance free, delivering high torque and high operating speeds.

Controller

The intelligent controller unit can be programmed for connection to any security/alarm systems, is self monitoring and calibrating, has memory for all data on door stoke and brake positions.

UPS

The operator has built-in uninterrupted power supply (Battery Back UP) operation and security during power failure.

Belt Drive

Drive is by way of toothed belt, which is reinforced with fiberglass tensile members, and has nylon facing surface for tooth protection on the pulleys. This combination produces silent accurate operation.

Tracking

The track is self-cleaning duel linear. The upper track is made of harder stronger alloy 6351T6, and can be replaced without moving the transom. The wheel trolley is fitted with anti-rise wheels, resulting in very firmly fitted doors with operation free of any racking.

Locking

Electromechanical Locking:

An electric lock option is available to give total security and can be adapted where manual locking cannot be achieved, i.e. frameless toughened Glass doors. Lock is the microprocessor controlled electric locking system. The microprocessor monitors all aspects of the lock functions. E.g. To ensure the door is fully closed when the lock is 100% engaged. Terminal outputs are available to signal to security system both door positions and lock status.

Optional

Monitoring and Control Systems (MACS):

System where by the automatic door operator can be programmed/adjusted from remote location shall be an independent control panel to monitor, adjust & control operations.

Features:

Can only be accessed through security PIN code
Integration to most building security management systems
Monitoring of doors on opening and closing positions
Choice of preset variable hold open time (0-30 secs)
To indicate: status of alarm, power failure or battery failure.
Display fault/malfunction
Make adjustments to operating parameters
On-line factory diagnosis & rectification via modem/internet

Safety

Door operation will automatically reverse in either direction if movement is obstructed, the sensitivity setting is programmable.

Warranty

All ADC units are covered by a 12 months parts warranty and a 12-month labor warranty; an extended warranty plan is available through an optional maintenance agreement.